На главнуюЛюди и блогиПохожее видеоЕще от: LearningZone

Throttle body repair. Idle air control cleaning & repair.

Оценок: 1028 | Просмотров: 282187
Here I am showing procedure to remove throttle body from a car and service it by cleaning and washing. The procedure could be applied to most cars. Here is the url for blog if you like to read: diycarmaint.blogspot.com
Категория: Люди и блоги
Html code for embedding videos on your blog
Текстовые комментарии (321)
mansooriqbal abbasi (8 дней назад)
I had Toyota Camry 2001 when I parked it in sun light its shows engine check light and engine oil light and car becomes little heavier while under cover parking car had no issues pls advice I go to lot of workshop but not found any solution
Ray Hughes (1 месяц назад)
Excellent tutorial. Used same technique to clean a Celica 2zz-ge IACV .
Cosmic Taco Cat (3 месяца назад)
Nice video. It was pretty satisfying to see it spinning so freely compared the before.
ali ejaz (3 месяца назад)
Sir mujy tu ap koi pathan lagty hain
LearningZone (3 месяца назад)
جی میرے بھائی پٹھان ہونا کوئی بری بات تو نہیں۔
Roadies Rider (3 месяца назад)
sir aapne konsa solvent used kiya hy is video my
Roadies Rider (3 месяца назад)
+LearningZone thanks for rply
LearningZone (3 месяца назад)
This is regular gasoline or petrol for cleaning. Anyhow you can use wd40 or special carburetor cleaner.
Pretty Sure (3 месяца назад)
What solvent are you using? Thanks
Dave Slingbart (4 месяца назад)
i just did this on my 2004 Scion XB, it has the same 1.5L engine, and it seems to run smoother at idle now. I didn't have any real bad issues, but watching you take apart the whole IAC gave me confidence that i wouldn't break anything, but those 5 point screws?? WTH! I improvised with an Oscillating Multi-Tool and cut a slot in the screws to use a flat head screwdriver to remove them. upon startup i had to erase 3 codes that appeared P0102, P0113 and P0511 and it is all good. Thank you for a Quick and Great Tutorial. :)
Romeo Madjantika (4 месяца назад)
Ok I have a problem with my premio 97 code 33 I already clean de iac valve still check engine Licht on what can bi the problem
Nasir Shaheen (4 месяца назад)
Dear I have corolla x 2002 1.3 2nzfe engine. Earlier its fuel economy was 14 kms per litre in local but now its around 10. I changed fuel pump, injectors, plugs,cleaned throttle, all sensors and catalaytic converter too. Nothing left but still problem is not solved. Checked tappets too. It gives unburdened fuel smell in morning and feels to be low in power on hilly areas. There is no check engine light also engine is in good condition. Plz give ur suggestions. Thanks
Nasir Shaheen (4 месяца назад)
LearningZone thankyou sir. I will as suggested by ur goodself and will share results soon
LearningZone (4 месяца назад)
Seems your car is running rich due to some reason. A scanner and a well educated technician in automotive field can diagnose by looking at short term fuel trims and long term fuel trims. Also oxygen sensors data can also help. For engine condition supposition will not do. Better confirm all your engine four cylinders with compression testing. If any of the cylinder varies more than 14psi among them you have a problem in that cylinder. Also any of the cylinder compression may not be less than 100psi. You may watch one of my videos on engine compression testing on my channel. Best wishes.
Willy Prasetya (4 месяца назад)
After watching this video, I will do it by my self to clean the throttle body on my Toyota Vios 2003. Thanks so much sir, greeting from Indonesia. Salam
Willy Prasetya (4 месяца назад)
LearningZone dear sir, I have finished cleaning my toyota vios 2003 throttle body. But there's a problem with the rpm when the AC is ON rhe rpm going down, when AC OFF rpm going up. Can u tell me what's wrong?
LearningZone (4 месяца назад)
Wish you very good luck with your throttle body service. You may share your excellent results and feeling after your service here with us and celebrate your joy with us too! Stay tuned and blessed.
Aleem Uddin (5 месяцев назад)
Sir plz app apna number muje send kejey plz mre es number pr 03359246137.plz Sir
Moin Gujjar (7 месяцев назад)
Sir wonderful lecture thank you
Zia Ul hassan (7 месяцев назад)
Dear sir your way of teaching is wonderful. you are best teacher .God bless on you thanks for up loading videos different topic .Ma Sha All you have sound knowledge . best regards
Ejaz Khan (7 месяцев назад)
sir wonderful lecture
Nijas ec (7 месяцев назад)
Can I use alcohol to clean ?
LearningZone (7 месяцев назад)
You can use any solvent of your choice.
Nijas ec (7 месяцев назад)
Or carb cleaner ?
Jimmy Favereau (7 месяцев назад)
subbed my friend and perfect timing for my situation.. many blessings and please protect yourself! skin absorbs those toxins so be safe! I love my 2000 Echo haha heres a manual for anyone interested.. http://caphector.com/atoyota/TableOfContents/manual.html God Bless All
LearningZone (7 месяцев назад)
You must love your Echo and same way your wife too! Lol. Stay blessed.
LearningZone (7 месяцев назад)
That's great dear friend if it helped you! You are right. One must avoid touching chemicals and oils due to their toxic nature. Best regards. Stay tuned and blessed.
Khan Jani (8 месяцев назад)
thanks brother nice job really very good,,,,
LearningZone (7 месяцев назад)
Thanks dear friend. Stay tuned.
Mangtu Kulria (8 месяцев назад)
How to arjest these idle screw
Mangtu Kulria (8 месяцев назад)
Hyundai eon me rpm ka kse pta chalega to idle ko kse fix kre
Mangtu Kulria (8 месяцев назад)
Eska pickup pr koi effect hota hai kya
LearningZone (8 месяцев назад)
You should not change the factory settings. But if some one already did so then you can do it in car setting it and looking at rpm. Set to some 700 rpm idling.
Baskar Baskar (9 месяцев назад)
i have honda jazz old model car, if idle is low the car mileage will increase?
LearningZone (9 месяцев назад)
Idling is not dealing with fuel economy as long as you are not keeping your car start when it is not in use or you are not running it. People don't do this normally. But sure good idling is nice in feeling and your ac is working smoothly when your car idles properly. Regards,
Silas Aqui (9 месяцев назад)
how did you tighten the 2 screws on the iacv
Screw göögIe (7 месяцев назад)
its a special bit needed, its like torx, but with 5 point star instead of 6 point star. they go under the name pentalobe, or ts bits. they are a bit hard to come by, but try at auto shop or similar. or ebay/amazon
LearningZone (9 месяцев назад)
Using a screw driver.
Sifat Oishique (9 месяцев назад)
Sir, I had to adjust my low idle rpm , and i fixed it by adjusting the Throttle stop screw, and it also worked. But then heard there's another screw called Idle Air Adjustment Screw, which is there specially for this purpose of adjusting idle air flow? and that the Throttle stop screw should not be changed but instead the idle air adjustment screw should be adjusted? I'm really having this confusion which one should i be adjusting and what are the difference between.these two?
Sifat Oishique (9 месяцев назад)
Sir what was the solvent that you used? Just water or any cleaning agent..
LearningZone (9 месяцев назад)
Sure you can. After cleaning and adjusting, do the hit and trial method to get the perfect adjustments.
Sifat Oishique (9 месяцев назад)
LearningZone LearningZone okay sir, i'll surely try it. But one more thing, is there any way i can get back the factory position for the throttle stop screw?
LearningZone (9 месяцев назад)
Dear friend if you have same arrangement car, your should clean the throttle body as I did in this video. The throttle cable screw should not be adjusted, the factory adjustment is the best ever adjustment as long as nobody tried it. What the people are telling, they are sharing their old days carb cars adjustment. So that was way too old and obsolete for fuel injected cars. You should do cleaning and washing and celebrate you success here with us! Wish you best of luck with your repairs.
oceantrolls73 (9 месяцев назад)
Amazing. Thank you. I cleaned the TB on my Toyota XA but did not open the Idle Air Control Valve that you showed. My issue was not resolved. Now that i have seen you do it I will reopen mine and do it right. Excellent presentation and knowledge. Thanks again.
LearningZone (9 месяцев назад)
Thanks dear friend for liking. Wish you best of luck with your repair. After success, celebrate it here with us. Best wishes.
Luis Manuel Martinez (10 месяцев назад)
Thanks for sharing. great video
LearningZone (9 месяцев назад)
Thanks for dropping such a nice comment.
Edgar Bravo (10 месяцев назад)
Good video 👍 I need subs 👍
LearningZone (9 месяцев назад)
Thanks dear friend.
etypercar (10 месяцев назад)
Best presented video of this procedure. Good presentation THANKS
Tim Newton (10 месяцев назад)
Does anyone know what size the bolts are on my 1992lexus ls 400 throttle body bolt
Jan Iqbal (11 месяцев назад)
Hi thanks for great video, what liquid you use for to cleaning throttle body and Idle air control with it?
Jan Iqbal (11 месяцев назад)
LearningZone thanks and appreciated.
LearningZone (11 месяцев назад)
It may not make any difference if you wash them with gas. But kaskets and o rings you should now wash in gas.
Jan Iqbal (11 месяцев назад)
Thanks for reply and do I have to not wash the electrical parts with gasoline or it doesnt matter if it get wash a bit with gasoline?
LearningZone (11 месяцев назад)
+Jan Iqbal thanks for liking. This is regular gasoline I am using to wash items with. Best regards,
H Gforce (11 месяцев назад)
hello sir, here in my country we have the same car/engine (jdm right hand wheel) but here we turn on the left side the steering wheel. your video is very helpful. Greetings from Paraguay.
LearningZone (11 месяцев назад)
Thanks for watching and liking. You are right the engines are the same and the steering arrangement is different from country to country. Best regards,
john doe (11 месяцев назад)
PERFECT BUT 1 THING SHOULD HAVE SHOWED MORE OF THE CAR WHEN IT WAS DIRTY MAN DAMN ALMOST GOT A 10 BUT FOR THAT 7
LearningZone (11 месяцев назад)
You are right dear friend. It had not been filmed. Next time hope!
M Ridware (11 месяцев назад)
Today i clean my 2004 camry throttle body and idle air control valve and my car is running smooth after cleaning...
M Ridware (11 месяцев назад)
LearningZone you are doing great job and providing full information and its very helpful, i like your work and your effort
LearningZone (11 месяцев назад)
That is great then. Thanks for feedback.
Trajan Augustus (1 год назад)
Great video, thank you. My 2004 RAV4 has some idle problems sometimes when I come to a quick stop. It clears up, but is still annoying. Had the throttle body cleaned but now I suspect the IAC.
LearningZone (11 месяцев назад)
Thanks for liking. Hope you solved your problem.
multiple miggs (1 год назад)
Cool Hindi/Mexican accent
LearningZone (1 год назад)
Isn't is good?
MrSarge99 (1 год назад)
In the video you showed a gasket for the IAC, but is there a gasket for the throttle body? Can it be reused if there is one? Thanks for the video.
LearningZone (1 год назад)
Yes there should be a gasket and must be used. You can reuse one if it is in good shape. Once we created one from a card board and worked well. Hope you may understand. Regards,
Тодор Тодоров (1 год назад)
Да де еба и индиеца
Naser AL JAHNI (1 год назад)
Thank you so much 👍🌷
LearningZone (1 год назад)
You most welcome always.
Mohammad Ashiqur Rahman (1 год назад)
Many many thanks.
LearningZone (1 год назад)
You most welcome always dear friend.
UberDom (1 год назад)
hey LZ, nice Vid. & nice accent btw :) I say nice cos you were detailed unlike auth.service guys who just spray on carburetor n valve n clean using rag that even a layman can do. + you cleaned it with solvent in front of us which was cool, & you took care not to dip it inside the bucket solvent instead u cleared it carefully which is normal procedure but I see BUFOONS dip it in solvent or petrol & take it out& charge big -- kudos. LZ , please clearly mention the following ; - I have rpm changes in idling & engine is heating up than normal before, will this solve it + carburetor setting in Hyundai Atos Eon manual5speed 2012car? --will spraying 3m cleaner alone on exposed carburetor after removing just intake pipe do good for a 43000kms car? -- is the air intake system need any cleaning spraying technique, besides replacing air filter? (please put video for it) -- I will also add fuel system cleaner inside full tank --most important, what was the solvent you used in the video for cleaning? I feel the above points for FULL SYSTEM CLEANING you are aware of & have videos for same. kudos once again..
LearningZone (1 год назад)
Thanks dear sir for liking videos and knowing the facts. I think your car have no carburetor but if may have a throttle body to be cleaned. You may need to clean your throttle body as I have shown here in this video and also I have further more videos on the topic on my channel. You may watch them for further understanding. You can spray any cleaning solvent in the air system. It will not cause any damage or problem. I am using regular car gas for cleaning as it is cheap and easily available and doing awesomely. If you are about to add cleaning liquid with fuel, it also works by I am preferring to clean the injectors outside the car. If you want, you can replace the fuel filter inside the fuel tank. I think I have upload videos on that. Or not then I would upload them soon.
steve McQueen (1 год назад)
Go pound slurpies
LearningZone (1 год назад)
Go ahead and apply it on yourself. Nobody stops you from because you are deserving to that.
steve McQueen (1 год назад)
is this injun shootin speed? holy shit
LearningZone (1 год назад)
What happened to you? You need a good treatment!
bisrama (1 год назад)
Great Job, Thank you!
Rommel Reyes (1 год назад)
are you having a hard time breathing? it sound like you need to catch you breath
LearningZone (1 год назад)
Can you help me?
Daniel Crowden (1 год назад)
thank you so much mate, i just fixed my sons car toyota echo with your instruction, it was the best help.
LearningZone (1 год назад)
That is great if the video helped you! The purpose of the video was to help people in bad situation. Hope you may subscribed the channel. If not yet, please subscribe. Regards,
James Harris (1 год назад)
I assume actuator last a lifetime, Does unplugging it at idle and that it goes lower mean its good.?
LearningZone (1 год назад)
Maybe you are right. But cleaning after certain time is a must as it is getting too much dust and dirt.
lizard944 (1 год назад)
For anyone who wants to know, those two screws are 5-point tamperproof. The only place I found them, other than online order, is Pep-Boys. #9684 T-20 made by CTA MFG Corp. Cost around $5.00 US
Luis Manuel Martinez (10 месяцев назад)
thanks for the info!!
Manuel Sanchez (1 год назад)
Thank you for sharing.
LearningZone (1 год назад)
That is my pleasure dear friend. Keep watching my channel. there are many video on the same and different topics and many will come soon. Regards,
lizard944 (1 год назад)
Thank you for your hard work. You help a lot of people. God will be good to you!
LearningZone (1 год назад)
Thank you very much for liking video. You are right this video helped a lot of people on their cars most important and most critical part throttle body. As I learned it so I shared with others to give them help on this important part. Hope you may find my other videos also interesting.
Bert Cochran (1 год назад)
thank you for your time.
LearningZone (1 год назад)
That's my pleasure. You may watch my other throttle body repair videos on my channel to get even more understanding of throttle bodies so that if you will attempt such a job on your car, it will be easy enough for you. Best regards,
Bu Rakan (1 год назад)
The bolts has been damaged and I cannot open the IAC .. any recommendations
john doe (11 месяцев назад)
ROTORY DRILL THEM HOES
Bu Rakan (1 год назад)
LearningZone thank you man you just safe my money
LearningZone (1 год назад)
Wish you good luck with your repair! Try to cut their heads using a hack saw and go for new bolts. They should available easily from your local market. Hope this will work for you. You may watch my new video on the same subject on my channel to get even more understanding of the job. Here is the link: https://www.youtube.com/watch?v=lsvpWJG-dK8
chu pong leung (1 год назад)
HI. The video is very good. May i ask what kind of cleaner have you used to clean the throttle body in the video?
chu pong leung (1 год назад)
Thank you sir.
LearningZone (1 год назад)
Wish you good luck with your repair! The cleaner and solvent used in the video is regular gas (Petrol). You can use anything like gas, WD40 or carb cleaner. You may watch my new video on the same subject on my channel to get even more understanding of the job. Here is the link: https://www.youtube.com/watch?v=lsvpWJG-dK8
xlr8 Gaming (1 год назад)
By watching this video i myself opened, cleaned and mad it free. Now working excellent. For the last 2 days i was roaming around mechanic who failed to fix the vibration problem of my 1nz fe engine. Thanx alot.
LearningZone (1 год назад)
That is great dear friend if you solved your Toyota problem with success. This is the purpose of the video. Here on the following url there is another video on my channel recently uploaded. You may watch it and get a little more understanding if you may do the job again. Also there is a blog associated with this video you already watched and the blog url is here in the description. You may give a look to that and get some more idea for future. Also I will upload another video soon on latest Toyota drive by wire system throttle body cleaning. You may subscribe if you like to get notification on each upload. Have good rides on your Toyota without problems! here is the url: https://www.youtube.com/watch?v=1EI17xW6CMc
Fernando Valentin (1 год назад)
Learning zone can u please tell me whats wrong with my car?i have changed the thermostate and the fans are working good.and still overheating.did i put wrong the thermostate?is there any specific side to put it in?
Fernando Valentin (1 год назад)
thank u.Learning zone.i'll check it out.
LearningZone (1 год назад)
The spring side of the thermostat should go towards the engine. Hope you fixed it right but for the overheating there will be some other definite reason. The very common and worst reason is a fully or partially blown head gasket. You may watch some other video on my channel how I tested for a blown head gasket. If you do that simple test, you will confirm that your head gasket is blown without removing anything from your engine. Search for that video yourself on my channel I have no idea in which date and time I uploaded that. Maybe for one Toyota Cressida I did that. Hope you may understand. Regards,
Rose Ly (1 год назад)
you sir just saved me from all these headaches! My vehicle been rough idle and I couldn't figured out why until now, to check the IAC. THANK YOU!
Razzi S (1 год назад)
LearningZone hi, my car fiat linea bifuel CNG halts while clutching or coming to a stop. the RPM suddenly drops below 500 and finally halts. Changed air filter, cleaned throttle body, but no success. some times I also get low oil pressure indication. pls share the possible causes awaits your reply.
LearningZone (1 год назад)
Thanks for liking video. That is great if my video may help you. Please watch my other video on the same subject I upload on my channel. Here is the link for that: https://www.youtube.com/watch?v=1EI17xW6CMc
istván Ifj Jagadics (1 год назад)
Thank you from Hungary!
LearningZone (1 год назад)
Thanks for liking video. That is great if my video may help you. Please watch my other video on the same subject I upload on my channel. Here is the link for that: https://www.youtube.com/watch?v=1EI17xW6CMc
Walter Vogel (1 год назад)
Thank you for the great video . Very nice . I'll do it tomorrow myself .
LearningZone (1 год назад)
Thanks for liking video. That is great if my video may help you. Please watch my other video on the same subject I upload on my channel. Here is the link for that: https://www.youtube.com/watch?v=1EI17xW6CMc
TrueVintageRnBFan (1 год назад)
Sorry, im going to the mechanic.
LearningZone (1 год назад)
Sure you may go and repair your job but it is good that at least you may now understand what the mechanic will do with your vehicle. Also you will be able to supervise his job with excellence. Regards,
Sean Lane (1 год назад)
Thank you for taking the time to post this!
LearningZone (1 год назад)
Thanks for liking video. That is great if my video may help you. Please watch my other video on the same subject I upload on my channel. Here is the link for that: https://www.youtube.com/watch?v=1EI17xW6CMc
Dhaneesh Virwani (2 года назад)
What solvent is used to clean throttle ?
john doe (11 месяцев назад)
U RITE ABOUT THAT THATS WHAT I ALWAYS USE ITS CRASY PAING FOR CARB CLEANER 4$ A CAN SOME PEOPLE WILL BELEAVE ANY ENDORSEMENT TRIAL BY ERROR THE ONLY WAY U LEARN ANYTHING, CAN U SAY U CAN FIGHT IF U NEVER HAD YR ASS WHOOPED NOPE GET YA ASS WHOOPED A FEW TIMES U WILL LEARN TO FIGHT LOOK IT UP ITS TRUE ON MYFOOTOUTSIDEYAASS.COM HEHE
LearningZone (1 год назад)
Regular gas. Watch this other video on my channel to get even more idea. https://www.youtube.com/watch?v=1EI17xW6CMc
Mike Sombrio (2 года назад)
Hello Engineer, thanks for the video. Very informative. I'm a Toyota Vios user (2005 model) if you may can share some idea about what i have notice in my car, when I turn-on all the lights during night time, I notice the engine will vibrate more and the RPM will decrease a little. Any suggestion about this? Thanks.
LearningZone (1 год назад)
Thanks for liking video. That is great if my video may help you. Your car needs the very same maintenance as the problem you described is due to a dirty throttlebody. Please watch my other video on the same subject I upload on my channel. Here is the link for that: https://www.youtube.com/watch?v=1EI17xW6CMc
Paul Armes (2 года назад)
The cooling system on that vehicle is in poor condition, Due to using tap water only.Try using a 50/50 mix of anti-freeze and distilled water to cut back on corrosion and deposits.
john doe (11 месяцев назад)
MAN RINSE THAT BITCH WITH HALF VINAGER AND GET A FULL TANK OF GAS LUCUAS FULL SYSTEM CLEANERPOP A WATER HOSE IN THAT BIT AND RUN THE HEAT ON HIGH ALL NIGHT WHEN U SATIFIED HIT THE INTAKE BOOT WITH SEAFOAM THE SPRAYCAN AND FOLLOW DIRECTIONS UR BABY BE SO CLEAN SHELL LOVE U ANOTHER 200,000 MILES
H G (2 года назад)
hello man...i clean my throttle body and the iac valve with carburator spray on my toyota corolla 2003...but my rpm now is 3200 rpm.... help meeeeeeee
Rashidbaloch Baloch (2 года назад)
hello dear sir I am still wating for your repaly sir
Rashidbaloch Baloch (2 года назад)
dear sir will you plz discribe the codes of ecu or fuse box about Toyota corolla or an other cars if you send for me these codes than sir plz contact me on my number I have whatsapp plz sir its a request to you
Rashidbaloch Baloch (2 года назад)
asallam alikum dear sir my name is rashid I am from Pakistan and I am also a mechanic of Manuel car and now I am also wana to learn computerize car work and I learn many things from you sir and I wana to be your papet if you don't mind sir of you get my msg than sir plz replay my ans and if you don't mind can I have your contact for suggestion ?
Ameer Hussein (2 года назад)
you know I opened the throttle body, but those 5 star screws turned me away, but I'll go at it again tomorrow inshallah. thanks for the video.
LearningZone (1 год назад)
Thanks for liking video. That is great if my video may help you. Please watch my other video on the same subject I upload on my channel. Here is the link for that: https://www.youtube.com/watch?v=1EI17xW6CMc
Ameer Hussein (2 года назад)
MashaAllah nice video, jazakallah khair
axenz axtiz (2 года назад)
I didnt understand the calibration. Can you give me the step? Thanks
Amee Hasa (2 года назад)
Dear Learning Zone: Thank you for your attention,,the engine can start normally when it's cold .but never can start and become heavy when the Engine is hot ,I check the spark plug it works but not blue spark it's orange color ,the engine size 2.0 I watch ur video I try to open this system because I open every things in ,,thank you
Aura Emali (1 год назад)
LearningZone my engine starts and goes off immediately. what might be the cause?
LearningZone (2 года назад)
As I asked you before you may test parameters like spark and fuel injection pulses when the engine is hot and reject to start. Then you will confirm which parameter is missing and make some conclusion from where that particular parameter is missing. If you will get something missing then your engine mechanical is OK but dig behind that parameter which is going to miss. Hope you understand my point. Regards,
Amee Hasa (2 года назад)
I have Elentra 2004 it's start normal after one hours when the engine hear if I make off I can not start the engine again need time until the engine become cool so hope advise me what I should go,thank u I change all sensor I change fuel pump I change wire of ignition
LearningZone (2 года назад)
Thanks for comment dear sir. It needs further more testing that what parameter to the engine is stopping it from starting in hot condition? You may check ignition, fuel injection pulses while such situation is happening. Sure there will be something missing. Then at the same time if the fuel injection pulses are missing, you may confirm security light that it should operate as normal. Normally security light stop blinking or disappears when everything is OK and car receives its own key. If there is some issue with your security, your car anti theft system needs checkup or replacement. For testing fuel injection pulses and security testing, you may watch my other videos on my channel. Regards,
when i switch on the air condition and press gas the car concuss for 3 second then disappears
Vijent Carlo (1 год назад)
اللهم صلي على محمدradireater buis wordhaart
LearningZone (2 года назад)
What a nice channel logo and channel name Masha Allah! Probably you have the same problem with your car. Better clean your car throttle body one time and you will feel the difference. Regards,
Chris5062284 (2 года назад)
Thanks for the video! Very helpful
LearningZone (2 года назад)
Thanks for liking and subscription. Regards,
Lao Han Tun (2 года назад)
Thank you mate..
LearningZone (2 года назад)
Thanks for liking and subscription. Regards,
HamHam (2 года назад)
can this remove a whistling noise?
HamHam (2 года назад)
+Tuneman1984 yeah !
Tuneman1984 (2 года назад)
Does yours whistle under light acceleration but go away on heavier or no throttle? That's what mine does and I'm wondering the same thing.
oleefree (2 года назад)
wow it's work thanks for that .keep on
LearningZone (2 года назад)
Thanks for liking and subscription. Regards,
sasin. sasin. (2 года назад)
good thank
LearningZone (2 года назад)
Thanks for liking and subscription. Regards,
gas1989 (2 года назад)
Good job sir. Thanks for sharing .
LearningZone (2 года назад)
+gas1989 Thanks for liking video. This video helped lot of people solving their idle speed for free. The sad thing here is even 22 people disliked this video till writing this comment. I don't know why people are disliking such videos? Did they pay me for that and the video was not according to their expectations? I know these people capacity, unfortunately they have no capacity to pay anybody a single penny! Regards,
Ken (2 года назад)
Unbelievable. Your channel is perfect helping people and educating all over the world. I'm very grateful and appreciate your videos. I have subscribed and I look forward to seeing more of your videos. If you have time, can you answer the following question: I have a 2003 Toyota corolla, automatic transmission, with 145,000 miles that I just bought. When the car is at normal temperature, and I stop at a red light with the car in drive, my idle is at 650rpm and the body of the car vibrates more than usual. I replaced all motor mounts. do you think I can clean the throttle body to take care of the problem? My transmission is running fine, but there is a slight vibration when slowing down to stop from second to first gear. Also, I don't think the previous owner changed the transmission fluid. is it safe to flush the transmission and place new fluid?I heard that transmission flushing can make the transmission break down faster when it's a high mileage transmission that hasn't been flushed. Thank you for the excellent knowledge and education!
LearningZone (2 года назад)
+Ken I thing it is not required to flush the transmission if is running without issues. The flushing can fail your transmission!
Ken (2 года назад)
Thank you for your answer! I will definitely check for a misfire! Would you flush the transmission with 145,000 miles if you didn't know if the transmission was ever flushed?
LearningZone (2 года назад)
+Ken Thanks Ken. This would be a good idea to clean your throttle body according to my instructions. It will may solve your idle problem. Also you may check your car for any misfire if it is there. I have a video on my channel to identify and repair misfire on such car. In case of misfire also the car will vibrate. The transmission issue you should only change the fluid and filter and change them a little frequent than the recommended 60000 miles. It will flush the transmission in more safe way than you are doing a regular flushing. Sure there would be chance of failure if you are going for regular aggressive flushing. So better you should avoid that. Regards,
Ilian Nachev (2 года назад)
If I were you, I would have replaced the bolts so I would have the right tool to remove them next time... :)
LearningZone (2 года назад)
+Ilian Nachev That would not be a bad idea. Attempt it when you will face such situation in future. Regards,
nick amar (2 года назад)
tahnk help alot
LearningZone (2 года назад)
Thanks for liking and subscription. Regards,
Ahmed Ali (2 года назад)
سؤال،اني سيارتي كورولا 2005 هل توجد مشكلة اذا فتحت ثلاجة المحرك وانظفهه خارج السيارة ؟وشكرا
LearningZone (2 года назад)
+Ahmed Ali حسنا ليس هناك مثل هذا المشكلة النظيفة التي المحركات . أفعل نفس الشيء في هذا الفيديو. التحيات
Ahmed Ali (2 года назад)
+LearningZone شكرا على الرد لكن انا لا اقصد مبخر مكيف السيارة،اقصد ثلاجة المحرك الموجوده بعد الثروتل الهواء..يعني المتصلة بالثروتل يصير افتحهه وانظفهه وشكرا
LearningZone (2 года назад)
+Ahmed Ali شكرا ل تعليق صديقي العزيز . أعتقد أنك تعني المبخر مكيف الهواء تحت لوحة القيادة . ثم إذا كان سيئا ، يمكنك استبدالها عن طريق فتح كل لوحة من السيارة ، وسوف تحتاج لملء الفريون مرة أخرى بعد الصيانة. لدي شريط فيديو على نفس كورولا على قناة بلادي القيام بهذه المهمة . إذا كان سؤالك مختلف ثم الرجاء شرح مرة أخرى أبعد من ذلك. التحيات
sanjay sukumar (2 года назад)
Super informative. DIY becomes a possibility with your videos. Cheers:)
LearningZone (2 года назад)
Thanks for liking and subscription. Regards,
A T (2 года назад)
Thanks for the video. A little long but very helpful for the back-yard mechanic.
LearningZone (2 года назад)
Thanks for liking and subscription. Regards,
paalu84 (2 года назад)
Dear sir, I want to ask that can I use petrol instead of this cleaning solvent ??????.
LearningZone (2 года назад)
+paalu84 Off course you can use Petrol. But somewhere it some dirt is very hard to remove by Petrol, you will need the solvent.
Cathy Buckley (2 года назад)
Thank You, this was very helpful & easy to understand, I've subscribed so i can learn much more about my car & hopefully save myself some $$,
LearningZone (2 года назад)
+Cathy Buckley Thank you very much dear friend for liking video and for subscription. Hope you will learn a great deal from my skills. I am uploading regularly. My goal is same to save your $$$$$! Hope you will watch and follow my channel regularly and will give your awesome beautiful comments!
Btechnology Bgroup (2 года назад)
Solution for the Problem of Honda Accord 2005 hi,  i hope that you all will be fine. :) As my experience this problem occurs from TPS itself, Because PCM thinks the throttle is wide open that’s why gear stuck in the park and PCM won`t let the solenoid to open state for the safety of gear box.  i was facing the issue on my accord 2005 since 2 days. Due to the sand storm my IAC was stuck and rpm was high i decided to clean the throttle body and i dissembled and cleaned it. after re-installing  everything was fine rpm was high little but gear stuck into park i did the RELEARN procedure for PCM several times to get out of the stuck state. RPM problem was gone but still gear was stuck in the park.  I talked to my mechanic he said take out the complete throttle body again reassemble it and reinstall again problem would be gone, Anyways everything was as it is and took out the IAC cleaned it and throttle body with solvent and again i reassembled,  After installation the problem was still exist stuck in the park. Then i decided to check all the fuses everything every electrical connector and fuses relays everything was ok..!!!! Testing & Symptoms: The brake lights work The brake stop light switch was OK. I have 12 volts on the yellow lead going to the release solenoid. The yellow black wire on the solenoid was not going to ground when the brake pedal was pushed. I placed a ground on the ground lead and the release solenoid worked every time. I verified continuity from the PCM pin 2 to the release solenoid ground wire I pulled all five connectors on the PCM and reseated them - park release worked for about 10 minutes then stopped working again. I hooked up my OBDII analyzer to confirm no trouble codes. The throttle position sensor was showing 9% at idle. I confirmed that no fuses were blown I pulled the throttle position sensor several times and reseated. I also applied a small drop of Deoxit on the 3 pins. Whenever I pulled the TPS connector, the solenoid worked every time. On the throttle position sensor, the 5 volt lead measured 5 volts, the position lead measured 0.5 volts at idle. The ground lead measured 0 volts.   (Take the test light connect to the battery`s –ve  connector and connect test light to the (Red+Blk) wire which called sensor signal wire to PCM and check the solenoid it will work while harness for the TPS is connected to TP sensor) anyways it’s not a solution just for knowledge purpose.   TPS Reading at the time of Problem. Throttle position 9% Wire color code ( Yellow+BLK/BROWN) Voltages were 5 Volts Ground good (Green+ BLK) reference voltages .5 Volts (RED+ BLK) ACCORDING TO THE HONDA Reference manual TPS spec should be as mentioned below. Throttle Position should be 0% On Red+Blk wire voltage should be .45 to .49 Volts Yellow+Blk wire voltage should be  4.5 to 5 Volts   but in actual what the honda says about TPS should be 0% and reference voltages should be .45 volts...  according to these measurements,  i could not disassembled the TPS because rivet tightened screws was holding the TPS so i started taping gently on the TPS from left to right to change its angle while OBDII code reader was connected to cell fone everything was visible via OBDII reader i took that angle from 9 % to 5% and then at that moment the solenoid works actually the reading was still higher for the PCM But it works,   Result is to changing the angle of TPS can take out from this trouble. I had read many solution as Honda recommend to change the throttle body which cost 1000 $$$$$.... to changing the angle for TPS can leads to the solution from this issue.   Hope this guide will help you this solution is based on my own experience. I hope it will help you a lot.   Thanks you !!!
Btechnology Bgroup (2 года назад)
i am working on accord 2005 five i had did pcm learn procedure for throttle body but problem stil exist looking for help.... thanks for your response. :d
Btechnology Bgroup (2 года назад)
+LearningZone after diconnecting the throttle position sensor pedal is working fine... i dont know whats a issue.:(((
LearningZone (2 года назад)
+Btechnology Bgroup Really never worked on any Honda for such problem. Sure I would tell you if I know. Better you make a little research on internet to get help from someone know the exact system. Regards,
Btechnology Bgroup (2 года назад)
+LearningZone can you please tell me the learn procedure for pcm may be i did it wrong for this model.????
LearningZone (2 года назад)
+Btechnology Bgroup If you relearned it and the problem still exists then you may check the system Electrical and Mechanically as it seems like something went bad which is causing your problem. If such is the case then proper repair will solve it.
Btechnology Bgroup (2 года назад)
recently i have cleaned the throttle body after cleaning rpm stays 1500 rpm and when i try to put in the gear when i press the pedal and try to release from the Parking to drive or any gear i am unable to do so... because the pedal solinoid does`nt engaged when i am dissconnecting the TPS connector then solinoid engaged normal... i don`t now why seeking your kind help please :(
Btechnology Bgroup (2 года назад)
+LearningZone after learn procedure i got some changes in rpm now the rpm is approximatly 1000 and pedal issue is still exist.... this happened after dissassembling the throttle body... could you please :(
LearningZone (2 года назад)
+Btechnology Bgroup What type and model of the car you are working on? Some cars need mechanical adjustment and some needs electronic scan tool adjustment after throttle body cleaning. So do it what ever is needed for your car to correct your idle speed to proper value. Some cars need sequential start and stop of the engine a few times to let the PCM learn the idle speed. So you may try this technique first if it works for you, it will save you from ton of work and effort. Share your success with us. Wish you good luck with your repair.
Your Dad (2 года назад)
My ATF dipstick is in the way of removing my throttle body on my 2003 Echo. Do you know how to remove the dipstick/dipstick housing?
Sandra Cardenas (2 года назад)
Same here. lol Just finished putting the throttle body back on. Thanks for replying:)
Sandra Cardenas (2 года назад)
Same here. lol Just finished putting the throttle body back on. Thanks for replying:)
Your Dad (2 года назад)
Lol, nope - I gave up and decided to live with the vibrations at idle.
Sandra Cardenas (2 года назад)
I have the same problem on my 05 Echo. Did you ever figure out how to get the throttle body out?
Reza Farahipour (2 года назад)
Thanks for the video. So what is the exact reason of idle rpm change when the electrical load changes?
LearningZone (2 года назад)
+Reza Farahipour In my experience in such case alternator is not at fault. If you will clean the throttle body, you will be able to solve such issue.
Reza Farahipour (2 года назад)
+LearningZone thanks for the reply! so it has nothing to with the alternator.
LearningZone (2 года назад)
+Reza Farahipour Thanks for your comment. Nearly the same dirty throttle body is one main reason for such a problem. In very rare cases it could be a vacuum leak in the system.
CARS LOVER (2 года назад)
remove the tps first ?
CARS LOVER (2 года назад)
maybe damage it with cleaner liquids friend ?
LearningZone (2 года назад)
+amjad amj Not always required. I am never removing if not really needed.
arshi khur (2 года назад)
So what is the solvent you are using? I don't have the toyota repair manual but just watching other you tube and reading blogs on the internet, I am at the assumption that there is a coating of molybdenum or other metals that could be destroyed b y scrubbing, I am not sure if that is true for echo? Also is it hard to buy vinyl gloves in your area? I don't think these chemicals are safe for the our skins. thanks again your video are very helpful.
arshi khur (2 года назад)
+LearningZone so what is the solvent you are using? thanks
arshi khur (2 года назад)
+LearningZone I have fixed some issues in my cars on my own and felt so stupid at the end of it that why was I begging others to help me when Its so easy to do it myself. Its hard to find a honest well trained mechanic as well as I hate being a dummy. In my area mechanics and dealership charge 100$ an hr as well as shop supply parts, etc,. Toyota echo are older well build cars. I hope to keep this car for ever. I am also reading books, and getting hand on training and might join a school, so no you tube is not my only mean of learning. I am going to drive for a long time why not be self sufficient. No my car is not giving me idle related problems and I am going to take your advice and leave it alone. If the body stays in good shape one day I hope to replace my gas engine for electric. I don't drive much and only drive couple of mile max 5 mile or so to do my errands.
LearningZone (2 года назад)
+arshi khur Thanks for your comment. If your car is giving trouble and you are planning to do the throttle body repair, just go for that. If you will read read and just make think on small small things, you would feel fear always. Also if you have problem in your throttle body, there is no other choice that you should clean it or replace it with a new one. If I would be in your place as I was while shooting this video sure I would go to the first choice! On the other hand if your car is good and is not giving any idle related problems then don't try cleaning throttle body for skill enhancement instead stay for good time when your throttle body gives you trouble and then sure you will also adapt the first choice and your decision will be even re-inforced when you will know the replacement throttle body price. Addressing your next question, this was not the only work with me to do or I am not an enthusiast to do the throttle body cleaning job as the first job of my life. I am always busy with such kind of jobs. In such a manner it is difficult to take care of gloves, shoes or other PPE. While we are working our aim is to focus on work and to take care the work with precision and in a fast way. Regards,
Netty Gretty (2 года назад)
Hi thanks for the great instruction. My 2004 corolla sedan is at 240000km. Yesterday without prior warning it started vibrating and idling rough and I couldn't get the speed up past 80kmph. I changed the spark plugs but it still does it. Should the IAC valve clean be the next step? What tool did you use for the 5 prong screws and what solvent do you use? Many thanks
LearningZone (2 года назад)
+Netty Gretty The problem you are stating seems a serious misfire due to any good reason. The best way here is to scan the car using a scan tool. It will ease you job. It could be no spark misfire, no fuel misfire or no compression misfire. I addressed almost all three type of misfire problems in my videos on my channel. You may search my channel for other videos to address your problem. The throttle body cleaning part is coming latter to bring your car to nice performance like new. First is to address the other issue like misfire. Hope you get my point. Share your success with us. Good luck. Regards,
Ibrahim Shahzad (2 года назад)
Salam I u Don`t mind!! I have a question for u!! what is the purpose of Water circulation in the IAC valve??
Ibrahim Shahzad (2 года назад)
+LearningZone thanks bro
LearningZone (2 года назад)
+Ibrahim Shahzad Just now see your comment. Great question! There are two purposes of water circulation in two designs of throttle body. In one design it is controlling the motion of IAC through a bimetalic strip using temperature. That one is a mixed electronic and mechanical type control. Old camry car had same system. Whereas in the other type like one here in the video have the only purpose of preheating the air which is entering to the engine for combustion. There is no other significant purpose of the water there.
sahab50094 (2 года назад)
very gooooood
LearningZone (2 года назад)
Thanks for liking and subscription. Regards,
toolman talal (3 года назад)
Did you use a scan tool to get the idle speed back normal?
LearningZone (2 года назад)
+toolman talal For this model it is not required. Regards,
Solution Netcomm (3 года назад)
Hi, Thank you for your video. Very instructive. I did clean my throttle idle valve and not sure I did put the black connector at the right place. But my problem is the same. high rpm at idle, but it change when I turn on fan in the car. It could be 1000 rpm with the fan off, but rise to 2000 rpm when I turn on the fan, not always but most of the time. There is nothing else in the car ( with electricity) that trigger same event. Turn on light, hasard, AC, , no change in RPM. Not sure where to look now, do you have an idea ? Thanks in advance
Solution Netcomm (2 года назад)
Thank you again for your video. What I did to test the valve, is to remove, the valve and put a full gasket between the valve and the throttle body. Did a bypass for my water so water doesn't come in the valve anymore. This confirm that my valve is defective and I ordered one. Right now, I don't have the choke and in the morning, idle is rough. But as soon as the temperature of the engine rise, idle is ok and I could turn fan on or off with no impact on rpm. Can't wait to receive my new valve.
Solution Netcomm (3 года назад)
+Solution Netcomm It is a Matrix 2003 Toyota, so similar to your car
Solution Netcomm (3 года назад)
+Solution Netcomm The rpm issue happen also with the fan off, it could be revving at 2000 and sometime more, seen 3000 rpm with the fan off. I disconnected the valve idle sensor and problem is the same. I've seen situation where I turn on the fan, and it barely change the rpm. I'm really lost.
Arturo Pavon (3 года назад)
Any videos on toyota 4runner 1992 on throttle body and vaccum lines having trouble my truck will not accelerate thank you for the help
apb38 (3 года назад)
Dude put some gloves on, that's solvent! Great video btw.
bruce murray (3 года назад)
Great job with video....just found this data ( see link ) as i try to work on a 04 Echo that has PO511 code 2000 to 2002 Toyota Echo Service Manual http://caphector.com/atoyota/TableOfContents/manual.html
UNIQUE CAMRY (3 года назад)
i cleaned my iac valve and try to get it to work by connecting the con ector and the vacume line hose ONLY. does that power it up? it wast sucking any air or soing anything but i could feel a little vibration inside. is it broken?
Kohatian Khan (3 года назад)
you are sharing a very precious information among the public, i wish i should have this all information , very nice
Sandra Edwards (1 год назад)
wajahat ali Khan I have aproblem with my carbine on 1991 121mazda sedan it is leaking fuel around top part of it and Al's the auto chock won't cut out can you help pls

Хотите оставить комментарий?

Присоединитесь к YouTube, или войдите, если вы уже зарегистрированы.