На главнуюОбразованиеПохожее видеоЕще от: LearningZone

generator engine assembling. Generator engine overhauling.

Оценок: 101 | Просмотров: 9735
In this video I will show how to assemble a generator or alternator engine. This video will cover details for crank shaft, piton, rings, harmonic balancer and cam shaft assembling in the engine housing.
Категория: Образование
Html code for embedding videos on your blog
Текстовые комментарии (20)
Mantu Mantu (8 дней назад)
Mukesh. Tudu
Jesse James (3 месяца назад)
Awesome video tutorial !!! Great step by step instructions !!!
LearningZone (3 месяца назад)
Thanks for liking and great to see your values comment.
nikstefos (6 месяцев назад)
Dear Sir thank you for your great video. I have LD186FA Air cooled diesel engine 10HP. The local technician replaced the crankshaft and timing gears because was broken. Everything reassembled as supposed to be, I hope. Now the engine rotates normally with power from battery, but not starting. Can you please advise me what could be the possible failures for this, as locally cannot be fixed further and I want to make that engine work again. Thanks in advance for you support.
nikstefos (6 месяцев назад)
LearningZone dear Sir, using the electric starter we managed to start the engine, but after 10-15 seconds stops. Is it fuel injector (new part) or Fuel pump problem. Checked both and found that fuel injector wasn't work as should. Reassemble it by the technician and engine worked as expected.
LearningZone (6 месяцев назад)
Yes on the top of valves there are tappets wich has a gap like 0.2mm on intake and 0.3mm on exhaust side for most Toyota gas engines. For your particular you can use these figures for reference or ask some specialist. That gap is critical and must be adjusted with care. Also give attention to fuel and timing issues as sometimes they are also very important. Regards,
nikstefos (6 месяцев назад)
LearningZone Dear Sir thank you for your reply. By tappers adjustment, you mean valve adjustment? I will check the engine tomorrow with another technician. Can I send you a video of the engine problem?
LearningZone (6 месяцев назад)
Dear friend there are three thing a must to start a diesel engine. Fuel, compression and timing. Check all four item should be there and should be corrected to get the engine started. They should look for tappets adjustment. Too loose or too tight tappets can be a cause of no start. Everything you must double check to get you engine back to life. Wish you good luck with your repair. Let share and celebrate your success here with us.
Ejaz Khan (6 месяцев назад)
sir wonderful lecture thank you
Moin Gujjar (7 месяцев назад)
Sir wonderful lecture thank you
Tariq Khan (7 месяцев назад)
Sir wonderful lecture thanks
Richard Lowe (9 месяцев назад)
Nice video - great job - although would have been nice to see it running
MrTwisted1977 (10 месяцев назад)
well done mashallah!!!
LearningZone (9 месяцев назад)
Thanks dear friend. You are great.
syed hussain (10 месяцев назад)
i fitted lpg gas kit in my 1800wats generator... ur prevoius video of how to clean generator lpg kit also helped me....
wyattoneable (10 месяцев назад)
Big thumbs up always!
tanveer khan (10 месяцев назад)
Salaam ustaad ji the gadget is sent today I hope you will receive it in one piece
zx8401ztv (10 месяцев назад)
That block/housing looked brand new, piston/rings also, very nice :-D The only part i would have taken more time with is refitting of the crank, i would never use a metal hammer on the shaft, the bearing in the crank case could get damaged. Shame he didn't have something to compress the piston rings, it would have gone in with less force, but using plastic is safe :-D With care that engine should last a loooooong time. Have you ever rebuilt an engine like this jahan?
tanveer khan (10 месяцев назад)
Another good video putting the piston in really does need a ring compressor but if there is not one available i have used a empty alluminium drink can if you cut the top and bottom off and slit it through the middle put the alluminium sheet inside the bore about 3 cm then push the piston in i replaced seals on a nitrogen accumulator using this method keep up the good work and demonstrations 👍👍👍👍👍👍👍
shoaib muhammad (11 месяцев назад)
good work and an excellent video

Хотите оставить комментарий?

Присоединитесь к YouTube, или войдите, если вы уже зарегистрированы.