Home
Videos uploaded by user β€œhameed wafa”
how to test frigidaire washer door lock assembly
 
02:39
Measure the wax motor (the brown piece on the right ) resistance. The normal reading should be close to 1500 Ohms, part #131763202
Views: 28969 hameed wafa
Kenmore dishwasher won't start
 
01:16
Reseted works OK 😊
Views: 39680 hameed wafa
GE Microwave Turntable Won't Turn
 
05:54
Microwave
Views: 34601 hameed wafa
whirlpool gold dishwasher wont start
 
01:18
dishwasher wont start clean light is flashing,fixed
Views: 21077 hameed wafa
F0E1 error code front load washer
 
05:10
Found defective wash motor,
Views: 8698 hameed wafa
Kenmore stove F11 error code fixed
 
05:14
Kenmore or Frigidaire F11 has the same meaning, communication problem between main board and display touch pad, or stuck key error, just by peeling it off and cleaning it, you would fix the problem πŸ˜€
Views: 14834 hameed wafa
Panasonic microwave runs for 2 seconds then shuts off
 
04:09
Checked everything, found out that my main control board was defective πŸ˜…
Views: 5216 hameed wafa
Kenmore dishwasher clean light flashing
 
00:44
Here how you reset relay on control board on this model clean light was flashing about 7 times
Views: 19292 hameed wafa
frigidaire gas stove F10 error code
 
04:44
A faulty RTD sensor probe is one of the causes for an F10 code or overheating oven. The sensor probe is supposed to detect the exact temperature in the Frigidaire electric range cavity and relay it to the oven's main control so it knows when to shut off the heating elements,
Views: 4622 hameed wafa
Diagnostic mode for Frigidaire affinity washer
 
03:58
At this moment in this washer the main problem is maintained control board not the motor, e56 error is high current to motor, but in this unit it is the main board. Also by holding start/pause and cancel at the same time with two fingers, will also show you the error code on this unit πŸ˜€
Views: 34036 hameed wafa
Samsung washer diagnostic mode
 
01:14
Error code AE6 = communication problem between inverter board and user interface board, check all the wires and connections, if didn't find any problem, replace main board located at the back πŸ˜€
Views: 74469 hameed wafa
Fridge keeps tripping the circuit breaker
 
03:06
Had defective compressor,
Views: 17701 hameed wafa
Maytag dishwasher leaks
 
04:06
This unit is more then 15 years old, and yes there was 3 Philips screws used on each side trim.
Views: 893 hameed wafa
Whirlpool dishwasher leaks from bottom
 
07:12
Replaced grommet fixed it πŸ˜‰
Views: 12148 hameed wafa
Microwave not heating
 
02:00
Microwave is not heating, replaced only diode and it works now.
Views: 26642 hameed wafa
Samsung microwave blows the fuse
 
15:07
Found defective micro switch fixed it.
Views: 3080 hameed wafa
Whirlpool washer calibration mode
 
02:21
After replacement of, main control board, wash motor, shift actuator, door lock, pressure sensor, you need to run calibration mode, otherwise the washer would not work properly πŸ˜‰
Views: 10452 hameed wafa
Samsung washer noisey and burning smell
 
04:05
Inspect unit, had defective bearing πŸ˜… the smoke is normal only when the bearing is defective πŸ˜‚ not all the time.
Views: 10649 hameed wafa
How to find leak on a fridge
 
01:50
Gave her 200 psi nitrogen used soapy water to find the leak, so I didn't had to replace evaporator and heat exchanger like always. Found the leak replaced the dryer filter and fixed it
Views: 20274 hameed wafa
GE microwave is dead
 
03:56
The problem was with noise filter. Repaired it, works fine now.
Views: 896 hameed wafa
Kenmore microwave won't start
 
02:23
Microwave won't start because the door was not latching properly or not engaged to the top micro switch fixed it πŸ˜€
Views: 9678 hameed wafa
Kitchenaid fridge leaks from water filter base
 
02:21
Couple problems fixed
Views: 4059 hameed wafa
GE dishwasher makes noise and not cleaning properly
 
04:59
Cleaned spray arms and found a piece of glass from drain pump or filter place
Views: 6611 hameed wafa
Estat dryer heater stays on
 
01:29
Estat dryer heater stays on part02
Views: 621 hameed wafa
Frigidaire affinity dryer is dead, πŸ˜‚ I don't know why I said washer πŸ˜†
 
06:02
Model number AEQ6000ES Part replaced thermal limiter 134120900 please clean your vent hose, before using the dryer 😘
Views: 607 hameed wafa
F3E2 error code maytag washer
 
09:37
Found 2 cracked wires at the temperature sensor at the back of the unit once wire was almost broken, that's why everytime it was agitating it was creating error code, resoldered it back, works perfectly fine πŸ˜€
Views: 2711 hameed wafa
E15 error code kenmore dishwasher
 
08:31
Leaked water
Views: 7526 hameed wafa
washer keeps filling with water
 
07:28
Even washer is off, it still fills with water, bad water valve fixed
Views: 31572 hameed wafa
Whirlpool dishwasher leaks from bottom part 1
 
07:15
Replaced grommet fixed it.
Views: 9640 hameed wafa
Whirlpool dishwashers control board fixed for free
 
11:34
Whirlpool dishwasher control board fixed for free
Views: 36035 hameed wafa
Kenmore elite dishwasher diagnosis
 
04:18
Dishwasher was not washing properly, wash motor was very weak,
Views: 11665 hameed wafa
Estate dryer heater stays on
 
01:27
Defective heat element shorted to ground part01
Views: 1364 hameed wafa
How to replace heater in Samsung dishwasher, from underneath  πŸ˜‰
 
02:34
I have seen everyone takes the front control board and front kick plate out to replace heating element on Samsung dishwashers, but this way it's easy.and yes customer was getting HE error code.which is heater error.
Views: 287 hameed wafa
Maytag bravos washer diagnostic mode
 
02:57
How to put Maytag bravos washer on diagnostic mood, it has no LCD display
Views: 18501 hameed wafa
Dacor venthood reset
 
00:56
This home owner was not able to turn off/on lights unless play around with fan switch ;)
Views: 892 hameed wafa
Copy of how to replace t.3 thermistor in Electrolux fridge on its ice maker
 
24:39
how to replace thermistor in Electrolux fridge on its ice maker.or how to replace t3 sensor on ice maker
Views: 3421 hameed wafa
Ultra wash quietguard standard, self diagnosis mood
 
02:04
This dishwasher was not functioning properly, there was stuck relay on the board, after self diagnosis it will reset everything and works OK z
Views: 3475 hameed wafa
F51 error code whirlpool cabrio
 
10:04
F then 51 flashes when there is a motor rotor position sensor (RPS) failure or lower harness problem. I recommend you to use loctite on the screw when retighting it back. I did not had loctite, it should be fine.
Views: 2223 hameed wafa
lexus is300 Cigarette lighter not working
 
05:11
my cigarette lighter was not working found the blown fuse and fixed it.
Views: 22009 hameed wafa
kenmore dryer makes thumping noise
 
02:40
samsung dryer makes thump noise
Views: 1160 hameed wafa
E3 error code samsung washer
 
02:50
E3 = Hall sensor and motor problem,control board, loose wire, bearing.In this case, bearing was broken. And hall sensor was not reading the motor speed, creating e3 error code.
Views: 54419 hameed wafa
Frigidaire affinitity error E48
 
05:32
code Fault condition Check E11 Fill time too long. (1). E13 Water leak in tub or air leak in air bell. (2). E21 Water not pumping out fast enough. (3). E23 Drain Pump relay is failed E31 Electronic pressure switch failure. (4). E32 Pressure sensor calibration problem. (4). E35 Pressure sensor indicates water overfill. (5). E38 Air trap clogged. (5). E41 Control board thinks the door switch is open. (6). E43 Door PTC Circuit Problem (6) E45 Line door sensing failure. (6). E47 Door PTC Sensing Open (6) E48 Door PTC Sensing Closed (6) E4A Door PTC Sensing Problem (6) E52 Bad signal from tacho generator. (7). E53 Low Voltage to Motor Control Board. (15). E54 Over speed. (9). E55 Under speed. (9). E57 High current on inverter. (8). E58 High current on motor phase. (8). E59 No tacho signal for 3 seconds. (9). E5A High temperature on heat sink caused by overloading. (8). E5C High Voltage experienced by MC. (13). E5D Communication problem. (10). E5F MC is continuously resetting. (10). E67 Heater sensing relay failure. (14). E68 Current leakage to ground on heater or fuse opened. (14). E71 Drum water NTC failure. (Tub heater) (15). E75 Water temperature sensor circuit. (12). E91 Communication error between UI board and main control board. (11). E92 UI_MB communications error (11). E93 Console or Main Board control problem. (11). E94 Main Board control problem. (11). E97 Console or Main Board control problem. (11). E98 Console control problem. (10). E9F Communication protocol (10) EA1 Power supply frequency out of limits (13). EA2 Power supply voltage too high (13). EA3 Power supply voltage too low (13). EA5 Main Voltage sensing failure (13). EAE Line safe relay sensing failure (13). EF1 Clogged drain pump. Unclog the drain pump. EF2 Too much soap. Advise customer to reduce the amount of soap they are using. EF6 Control Reset (17) EF8 Key Stuck Check all buttons
Views: 2586 hameed wafa
Dacor microwave intermittent heat
 
02:57
Found defective microwave switch replaced it, works fine now.
Views: 316 hameed wafa
Kenmore washer drum seized
 
02:22
Bearing is broken, not worth to fix.made by Samsung πŸ˜‰
Views: 460 hameed wafa
Samsung washer noisey and burning smell part 2
 
15:33
Ordered bearing to fix it unfortunately the problem was big 😬
Views: 4434 hameed wafa
Kenmore front load washer diagnostic
 
01:35
F21 = long drain
Views: 29895 hameed wafa
3E error samsung washer
 
03:47
Had broken bearing, motor was not able to move freely, motor, hall effect sesnsor, control board, and wiring checked OK.there is 5 pins on Hall effect sensor check between pin 1 and 5 also between 2 and 5 should get around 10 ohms, pin one and two is bestie each other and the holes are circle shape but pin 3 4 5 are the square shape holes
Views: 25031 hameed wafa